Design, Fabrication and Parametric Study of Bulk Current Injection Probe and Its Calibration Fixture | ||
| Journal of Communication Engineering | ||
| مقاله 8، دوره 9، شماره 1 - شماره پیاپی 18، فروردین 2020، صفحه 93-108 اصل مقاله (1.71 M) | ||
| نوع مقاله: Research Paper | ||
| شناسه دیجیتال (DOI): 10.22070/jce.2021.13338.1170 | ||
| نویسندگان | ||
| Seyyed Mohamad Javad Razavi* 1؛ Issa Mostafa Mashriki2؛ sayed hosein mohseni armaki3 | ||
| 1Faculty of Electrical & Computer Engineering, Malek Ashter University of Technology, Iran, Tehran | ||
| 2High Institute for Applied Science and Technology, Syria, Damascus | ||
| 3Electrical and Electronics Engineering Dept., Malek-e-Ashtar University of Technology, Tehran, Iran | ||
| چکیده | ||
| In this paper, the fabrication of a bulk current injection (BCI) probe using two different ferrite materials and a wideband rounded-shield calibration fixture or jig used to calibrate BCI probe are presented. Some optimization ideas are also investigated to increase their performance. The effect of change in various parameters such as slot distance, probe’s shield to probe’s core spacing and the inner surface of probe’s shield on the probe high frequency performance and insertion loss (IL) have been studied. Results show that increasing the slot distance improves the high frequency response of the probe and increasing the probe’s shield to probe’s core spacing would affect negatively on measured IL and decreasing the inner surface of probe’s shield improves the probe working bandwidth. | ||
| کلیدواژهها | ||
| Bulk current injection (BCI)؛ calibration fixture (CF or JIG)؛ electromagnetic Compatibility (EMC)؛ optimization؛ parametric study | ||
| مراجع | ||
|
1- RTCA/DO-160F - “Environmental conditions and test procedures for airborne equipment,” 2007.
2- Electromagnetic compatibility (EMC) -Part4–6: Testing and measurement techniques-Immunity to conducted disturbances, induced by radio-frequency fields, IEC Standard 61000-4-6, May 2006.
3- ISO Standard 11451-4: Road Vehicles-Vehicle test methods for electrical disturbances from narrowband radiatedelectromagnetic energy-Part4: Bulk Current Injection (BCI), June, 2006.
4- ISO Standard 11452-4: Road Vehicles- Component Test Methods for Electrical Disturbances from Narrowband Radiated Electromagnetic Energy-Part4: Harness excitation methods, Dec.2011.
5- IEC 62132-3, Ed.1: Integrated Circuit Measurements of Electromagnetic Immunity 150kHz to 1GHz, Part 3: Bulk Current Injection (BCI) Method, 2007.
6- Department of Defense Interface Standard, “Requirements for the Control of Electromagnetic Interference Characteristics of Subsystems and Equipment", MIL-STD-461E, Aug. 20, 1999.
7- Fischer Custom Communications BCI Brochure, Fischer Custom Communications, Inc.
8- H. Sekiguchi, T. Funaki, “Proposal for Measurement Method of Transfer Impedance of Current Probe,” IEEE Trans. EMC, vol. 56, no. 4, pp. 871-877, Aug. 2014.
9- L. W. Ma, C. Yu, “Correlation between Transfer Impedance and Insertion Loss of Current Probes,” IEEE EMC Magazine, vol. 3, no. 2, pp. 51-55, 2nd Quarter 2014.
10- F. Grassi, S.A. Pignari “Characterization of the Bulk Current of Injection Calibration-jig for the Probe-Model Extraction,” 2010 IEEE International Symposium on EMC, Fort Lauderdale, FL, pp. 344-347 , July 2010.
11- N. Toscani, F. Grassi, G. Spadacini, S.A. Pignari, “Circuit and Electromagnetic Modeling of Bulk Current Injection Test Setups Involving Complex Wiring Harnesses,” IEEE Trans. EMC, vol. 60, no. 6, pp. 1752-1760, Dec. 2018.
12- I. M. Mashriki, S. M. J. Razavi, S. H. M. Armaki, “Electromagnetic and circuit modelling of a modified design of bulk current injection probe calibration jig,” IET Science, Measurement & Technology, in IET Science, vol. 14, no. 9, pp. 715-721, Nov. 2020.
13- I. M. Mashriki, S. M. J. Razavi, S. H. M. Armaki, “Hybrid Model for Bulk Current Injection Probe,” Journal of Communication Engineering, vol. 8, no. 2, pp. 277-289, July-Dec. 2019.
14- I. M. Mashriki, S. M. J. Razavi, S. H. M. Armaki, “Analyzing the Resonance Resultant from the Capacitive Effects in Bulk Current Injection Probe,” Radioengineering, vol. 29, pp. 109-116, April 2020.
15- F. Grassi, F. Marliani, S.A. Pignari "Circuit Modeling of Injection Probes For Bulk Current Injection," IEEE Trans. Electromagnetic, Compatibility., vol. 49, no. 3, pp. 563-576, Aug. 2007. | ||
|
آمار تعداد مشاهده مقاله: 499 تعداد دریافت فایل اصل مقاله: 522 |
||